RTCA DO-283C-2024 PDF

RTCA DO-283C-2024 PDF

Minimum Operational Performance Standards for Required Navigation Performance for Area Navigation

$309.00 $618.00 -50%
Publisher
Product Code: RTCA DO-283C
Stock In Stock
Edition: C
Published: 12/12/2024
Number of Pages: 272
File Size: 1 file, 5.4 MB

Available Options

Product Description

PURPOSE AND SCOPE Introduction This document contains Minimum Operational Performance Standards (MOPS) for airborne area navigation equipment operated in a Required Navigation Performance (RNP) operational environment. The MOPS documents the minimum requirements and guidance for one functional part of the airplane system that is described and specified by the MASPS, DO-236(), and ED-75(). These standards specify system characteristics that should be useful to designers, manufacturers, installers and users of the equipment. In an attempt to ease the use of this document for the reader, ICAO has licensed RTCA to reproduce limited material as published by ICAO in references [4], [16], and [18] in Appendix A. These reproductions are used with permission. ICAO maintains all copyright benefits on the material. Equipment conforming to the requirements of this document is herein referred to as “RNP” equipment. The requirements of the MOPS are intended to be consistent with the definition of RNP developed by the International Civil Aviation Organization (ICAO) Performance Based Navigation (PBN) study group and enable PBN-based operational applications. This is because the MOPS presents a comprehensive set of minimum requirements for RNP that enables a manufacturer to develop equipment suited to designated system installations and PBN operational applications. The PBN manual navigation specifications represent end use criteria for aircraft systems and equipment that are oriented to specific operational needs, capabilities and performance. The result is that each navigation specification describes specific aircraft equipment, performance capabilities and functional requirements that, if common with the MOPS, are mostly just a subset of the total MOPS RNP requirements. Thus the RNP equipment that meets all of the requirements of this MOPS will not necessarily be the same as the RNP systems and equipment eligible in any one navigation specification even though they will have requirements in common. Barometric vertical navigation (VNAV) requirements are defined for aircraft that provide this capability to ensure accurate and predictable vertical paths. The VNAV requirements in this document are consistent with instrument approach procedures with vertical guidance (APV). Due to the wide disparity of climb performance of different aircraft types, this MOPS only addresses vertical path definition requirements for level flight and descent. Time of Arrival Control (TOAC) requirements are defined for RNP equipment that provide the optional TOAC capability. TOAC requirements and guidance were derived from material provided by EUROCAE WG-85 and are based upon projects in the European SESAR program. The committee also decided that to achieve the best alignment and implementation of RNP equipment to the planned operational requirements and applications, the MOPS should organize the appropriate requirements and guidance to fit the operational near term applications as well as allow for a step to far term applications. Compliance with these standards is recommended as one means of assuring that the equipment will perform its intended function(s) satisfactorily under all conditions normally encountered in routine aeronautical operations. Any regulatory application of this document is the sole responsibility of the appropriate aviation authorities. Section 1.0 of this document provides information needed to understand the rationale for the equipment characteristics and requirements stated in the remaining sections. It describes typical equipment applications and operational goals, as originally envisioned by Special Committee 181 then expanded by Special Committee 227, and forms the basis for standards stated in Sections 2.0 through 3.0. Definitions and assumptions essential to proper understanding of this document are also provided in this section. Section 2.0 contains the minimum performance standards for the equipment. These standards specify the required performance under standard operating conditions and stressed physical environmental conditions. Also included are recommended bench test procedures necessary to demonstrate compliance. Section 3.0 provides references to installation guidance material for installed equipment performance, and also describes the performance required of the installed equipment. Tests for the installed equipment are included when performance cannot be adequately determined through bench testing. Section 4.0 describes the operational characteristics for equipment installations and defines conditions that will assure the operator that operations can be conducted safely and reliably in the expected operational environment. Section 5.0 describes membership list. Appendix A contains glossary, acronyms, and abbreviations. Appendix B is removed. Appendix C contains navigation system requirements and infrastructure characteristics. Appendix D contains leg type definitions. Appendix E contains the WGS-84 earth model and geodesic path example Appendix F contains human factors considerations Appendix G contains CNS-ATM system considerations Appendix H contains temperature compensation requirements Appendix I is intentionally left blank. Appendix J contains examples of RNP Holding Pattern entries Appendix K is intentionally left blank. Appendix L contains an example application of Radius to Fix (RF) leg performance tests Appendix M provides guidelines for the collection and analysis of flight technical error (FTE) data. Appendix N contains Time of Arrival Control requirements. Appendix O contains an example of ETA compliance analysis Appendix P contains an example of VNAV compliance analysis Appendix Q contains examples of descent paths Appendix R contains application of statistical hypothesis testing to fault detection in ground-based navaids Appendix S contains details about flight planning with terminal route transitions Appendix T contains guidance on the use of position estimation error requirements The term “equipment” as used in this document includes all components or units necessary (as determined by the equipment manufacturer or installer) for the equipment to perform properly its intended function. For example, the RNP “equipment” may include: a computer unit, as well as associated sensor(s), an input-output unit that interfaces with existing aircraft displays/systems, a control unit, a display, etc. In the case of this example, all of the associated components or units comprise the “equipment”. It should not be inferred from this example, however, that every RNP equipment will necessarily include all of the foregoing components or units. The particular components of the RNP equipment will depend upon the design used by the equipment manufacturer, subject to the constraint that the equipment must meet the applicable requirements of this MOPS.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
RTCA DO-283C-2024 PDF

RTCA DO-283C-2024 PDF

$309.00 $618.00