Household and similar electrical appliances – Safety – Part 2-45: Particular requirements for portable heating tools and similar appliances (Commented Version)
Introduction: It has been assumed in the drafting of this International Standard that the execution of its provisions is entrusted to appropriately qualified and experienced persons. Guidance documents concerning the application of the safety requirements for appliances can be accessed via TC 61 supporting documents on the IEC website https://www.iec.ch/tc61/supportingdocuments This information is given for the convenience of users of this International Standard and does not constitute a replacement for the normative text in this standard. This standard recognizes the internationally accepted level of protection against hazards such as electrical, mechanical, thermal, fire and radiation of appliances when operated as in normal use taking into account the manufacturer's instructions. It also covers abnormal situations that can be expected in practice and takes into account the way in which electromagnetic phenomena can affect the safe operation of appliances. This standard takes into account the requirements of IEC 60364 as far as possible so that there is compatibility with the wiring rules when the appliance is connected to the supply mains. However, national wiring rules may can differ. If an appliance within the scope of this standard also incorporates functions that are covered by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as far as is reasonable. If applicable, the influence of one function on the other is taken into account. When a part 2
Scope: This clause of Part 1 is replaced by the following. This part of IEC 60335 deals with the safety of portable electric heating tools and similar appliances, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances. 3 Appliances not intended for normal household use, but which nevertheless may can be a source of danger to the public, such as appliances intended to be used by laymen laypersons in shops, in light industry and on farms, are within the scope of this standard. Appliances that may can also be used when mounted on a support are within the scope of this standard. NOTE 101 Examples of appliances that are within the scope of this standard are branding tools; burning-in pens; conduit-soldering tools; dehorning tools; desoldering irons; firelighters; glue guns; heat guns; household film-welding appliances; paint strippers; plastic-cutting tools; soldering guns; soldering irons; stripping pliers; thermoplastic conduit-welding tools. As far as is practicable, this standard deals with the common hazards presented by appliances which are encountered by all persons in and around the home. However, in general, it does not in general take into account persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction; children playing with the appliance. IEC 60335-2-45:2024 CMV © IEC 2024 – 9 – NOTE 102 Attention is drawn to the fact that for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may can be necessary; in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities. NOTE 103 This standard does not apply to: hand-held motor-operated electric tools (IEC 60745 series, IEC 62841 series); transportable motor-operated electric tools (IEC 61029 series, IEC 62841 series); appliances intended exclusively for industrial purposes; appliances intended to be used in locations where special conditions prevail, s
Contents:
- FOREWORD
- INTRODUCTION
- Scope
- 10 Power input and current
- 11 Heating
- 12 Void Charging of metal-ion batteries
- 13 Leakage current and electric strength at operating temperature
- 14 Transient overvoltages
- 15 Moisture resistance
- 16 Leakage current and electric strength
- 17 Overload protection of transformers and associated circuits
- 18 Endurance
- 19 Abnormal operation
- 20 Stability and mechanical hazards
- 21 Mechanical strength
- 22 Construction
- 23 Internal wiring
- 24 Components
- 25 Supply connection and external flexible cords
- 26 Terminals for external conductors
- 27 Provision for earthing
- 28 Screws and connections
- 29 Clearances, creepage distances and solid insulation
- 30 Resistance to heat and fire
- 31 Resistance to rusting
- 32 Radiation, toxicity and similar hazards