IEC 60519-12-2016 PDF

IEC 60519-12-2016 PDF

Safety in installations for electroheating and electromagnetic processing - Part 12: Particular requirements for infrared electroheating

$163.93 $327.86 -50%
Product Code: IEC 60519-12
Stock In Stock
Edition: 2.0
Published: 12/2016
Number of Pages: 72
File Size: 1 file, 921 Bytes

Available Options

Product Description

Safety in installations for electroheating and electromagnetic processing - Part 12: Particular requirements for infrared electroheating

Introduction: The scope of this standard covers a broad range of types and designs of infrared equipment which are used for many different purposes. This standard is intended to cover all industrial infrared equipment types, with some few exceptions provided in Clause 1. Many other types of electroheating equipment emit infrared radiation of hazardous levels, therefore IEC 60519-1:2015 provides all general requirements addressing optical radiation and this document provides specific considerations for infrared equipment and helpful methods. With reference to IEC 60519-2:2006 it has been agreed in TC 27 that this standard covers all kinds of infrared emission hazards of industrial electroheating installations and provisions not given in IEC 60519-1:2015. The discussion of infrared radiation assessment has become quite detailed in this standard, as for the industry there is not any single useful source available for simple, versatile, easy to use and cost effective measurement methods. The other principles for covering the risks caused by infrared radiation were: the manufacturer usually does not employ an expert in optical radiation measurement or has access to an optical laboratory with all the necessary equipment needed for elaborate measurements; operating staff with limited experience in radiation measurement is usually responsible for the task of performing the necessary measurements and will appreciate a simple and easy to follow guide; the scope of IEC 62471:2006 is limited to lamps

Scope: This clause of Part 1 is replaced by the following. Replacement: This part of IEC 60519 specifies safety requirements for industrial electroheating equipment and installations in which infrared radiation – usually generated by infrared emitters – is significantly dominating over heat convection or heat conduction as means of energy transfer to the workload. A further limitation of the scope is that the infrared emitters have a maximum spectral emission at longer wavelengths than 780 nm in air or vacuum, and are emitting wideband continuous spectra such as by thermal radiation or high pressure arcs. IEC 60519-1:2015 defines infrared as radiation within the frequency range between 400 THz and 300 GHz. This corresponds to a wavelength range between 780 nm and 10 µm in vacuum. Industrial infrared heating commonly uses thermal infrared sources with rated temperatures between 500 °C and 3 000 °C; the emitted radiation from these sources dominates in the wavelength range between 780 nm and 10 µm. Since substantial emission of thermal emitters can extend either to wavelengths below 780 nm or above 3 000 nm, the safety aspects of emitted visible light and emission at wavelengths longer than 3 000 nm are also considered in this document. This standard is not applicable to: infrared installations with lasers or light-emitting diodes (LEDs) as main sources – they are covered by IEC 62471:2006 and IEC 60825-1:2014; appliances for use by the general public; appliances for laboratory use – they are covered by IEC 61010-1:2010; electroheating installations where resistance heated bare wires, tubes or bars are used as heating elements, and infrared radiation is not a dominant side effect of the intended use, covered by IEC 60519-2:2006; infrared heating equipment with a nominal combined electrical power of the infrared emitters of less than 250 W; handheld infrared equipment. Industrial infrared electroheating equipment under the scope of this standard typically uses the Joule effect for the conversion of electric energy into infrared radiation by one or several sources. Radiation is then emitted from one or several elements onto the material to be treated. Such infrared heating

Contents:

  • FOREWORD
  • INTRODUCTION

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC 60519-12-2016 PDF

IEC 60519-12-2016 PDF

$163.93 $327.86