IEC 60695-11-20-2015 PDF

IEC 60695-11-20-2015 PDF

Fire hazard testing - Part 11-20: Test flames - 500 W flame test method

$163.93 $327.86 -50%
Product Code: IEC 60695-11-20
Stock In Stock
Edition: 2.0
Published: 04/2015
Number of Pages: 68
File Size: 2 files, 1.1 KB

Available Options

Product Description

Fire hazard testing - Part 11-20: Test flames - 500 W flame test method

Introduction: In the design of an electrotechnical product the risk of fire and the potential hazards associated with fire need to be considered. In this respect the objective of component, circuit and equipment design as well as the choice of materials is to reduce to a tolerable level of risk of fire even in the event of reasonably foreseeable (mis)use, malfunction or failure. Fires involving electrotechnical products can also be initiated from external non-electrical sources. Considerations of this nature are dealt with in the overall fire hazard assessment. The aim of the IEC 60695 series of standards is to save lives and property by reducing the number of fires or reducing the consequences of the fire. This can be accomplished by: trying to prevent ignition caused by an electrically energised component part and, in the event of ignition, to confine any resulting fire within the bounds of the enclosure of the electrotechnical product. trying to minimise flame spread beyond the product’s enclosure and to minimise the harmful effects of fire effluents including heat, smoke, and toxic or corrosive combustion products. This part of IEC 60695 describes a test method which consists of two small-scale fire test procedures carried out on materials used in electrotechnical equipment. A 500 W test flame is used as an ignition source. The test method described provides classifications which may be used for quality assurance, the pre-selection of component materials of products, or to verify the r

Scope: This part of IEC 60695 describes a test method consisting of two small-scale laboratory test procedures which is intended to compare the burning behaviour of different materials used in electrotechnical products. Vertically oriented bar specimens or horizontally oriented plate test specimens are exposed to a small flame ignition source with a nominal thermal power of 500 W. The test method uses two test specimen configurations to classify material performance. Rectangular bar-shaped test specimens are used to assess ignitability and burning behaviour, and square plate test specimens are used to assess the resistance of the test specimen to burn-through, as defined in 8.3.3. This test method only applies to materials that have been classified as V-0 or V-1 according to IEC 60695-11-10. This test method is only applicable to solid and cellular materials that have an apparent density of more than 250 kg/m3, determined in accordance with ISO 845. The method does not apply to materials that shrink away from the applied flame without igniting due to their thinness. The test method described provides classifications which may be used for quality assurance, the pre-selection of component materials of products, or to verify the required minimum flammability classification of materials used in end products. If used for pre-selection, then positive results shall be obtained at a test specimen thickness which equals the smallest thickness used in the product application. The results obtained provide some information about the behaviour of materials in service, but cannot by themselves assure safe performance in service. NOTE 1 Guidance on pre-selection is given in IEC 60695-1-30 [3]1. NOTE 2 Test results are influenced by material additives, e.g. pigments, fillers, and fire retardants, and properties such as the direction of anisotropy and the molecular mass. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the prepa

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC 60695-11-20-2015 PDF

IEC 60695-11-20-2015 PDF

$163.93 $327.86