IEC 61347-2-8 (REDLINE + STANDARD)-2024 PDF

IEC 61347-2-8 (REDLINE + STANDARD)-2024 PDF

Controlgear for electric light sources-Safety-Part 2-8: Particular requirements-Ballasts for fluorescent lamps

$171.50 $342.99 -50%
Product Code: IEC 61347-2-8 (REDLINE + STANDARD)
Stock In Stock
Edition: 2.0
Published: 05/2024
Number of Pages: 72
File Size: 1 file, 1.9 MB

Available Options

Product Description

Controlgear for electric light sources – Safety – Part 2-8: Particular requirements – Ballasts for fluorescent lamps

Introduction: This first edition of IEC 61347-2-8, published in conjunction with IEC 61347-1, represents an editorial review of IEC 60920. The formatting into separately published parts provides for ease of future amendments and revisions. Additional requirements will be added as and when a need for them is recognized. This standard, and the parts which make up IEC 61347-2, in referring to any of the clauses of IEC 61347-1, specify the extent to which such a clause is applicable and the order in which the tests are to be performed; they also include additional requirements, as necessary. All parts which make up IEC 61347-2 are self-contained and, therefore, do not include references to each other. Where the requirements of any of the clauses of IEC 61347-1 are referred to in this standard by the phrase "The requirements of clause n of IEC 61347-1 apply", this phrase is interpreted as meaning that all requirements of the clause in question of part 1 apply, except any which are clearly inapplicable to the specific type of lamp controlgear covered by this particular part of IEC 61347-2. The technical requirements in this document compared to IEC 61347-2-8:2000 and IEC 61347-2-8:2000/AMD1:2006 are essentially unchanged. Nevertheless, a new edition of this document could not be avoided, as without the introduction of dated references to IEC 61347-1:2015 and IEC 61347-1:2015/AMD1:2017, the fourth edition of IEC 61347-1:—1 would have been implicitly applicable due to the undated nature of the ref

Scope: This part of IEC 61347 specifies safety requirements for ballasts, excluding resistance types, for use on AC supplies up to 1 000 V at 50 Hz or 60 Hz, associated with fluorescent lamps with or without pre-heated cathodes operated with or without a starter or starting device and having rated wattages powers, dimensions and characteristics as specified in IEC 60081 and IEC 60901. This document applies to complete ballasts and to their component parts such as reactors, transformers and capacitors. Particular requirements for thermally protected ballasts are given in annex B. Ballasts for conventional operation of lamps at mains frequency are covered, while AC supplied electronic ballasts for high-frequency operation are excluded. Ballasts for conventional operation of lamps at mains frequency are covered, while a.c. supplied electronic ballasts for highfrequency operation are excluded. These are specified in IEC 61347- 2-3. Capacitors having a capacitance greater than 0,1 µF are covered by IEC 61048 and IEC 61049. Capacitors having a capacitance less than or equal to 0,1 µF are specified in IEC 60384-14. NOTE 1 AC supplied electronic ballasts for high-frequency operation are specified in IEC 61347-2-3. NOTE 2 Performance requirements are the subject of IEC 60921.

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC 61347-2-8 (REDLINE + STANDARD)-2024 PDF

IEC 61347-2-8 (REDLINE + STANDARD)-2024 PDF

$171.50 $342.99