IEC 62439-3 (REDLINE + STANDARD)-2016 PDF

IEC 62439-3 (REDLINE + STANDARD)-2016 PDF

Industrial communication networks-High availability automation networks-Part 3: Parallel Redundancy Protocol (PRP) and High-availability Seamless Redundancy (HSR)

$509.45 $1,018.89 -50%
Product Code: IEC 62439-3 (REDLINE + STANDARD)
Stock In Stock
Edition: 3.0
Published: 03/2016
Number of Pages: 544
File Size: 1 file

Available Options

Product Description

Industrial communication networks – High availability automation networks – Part 3: Parallel Redundancy Protocol (PRP) and High-availability Seamless Redundancy (HSR)

Introduction: 0.1 General IEC 62439-3 belongs to the IEC 62439 series “Industrial communication networks – High availability automation networks”. It specifies the PRP and HSR seamless redundancy protocols. It was adopted by IEC TC57 WG10 as the redundancy method for demanding substation automation networks based on IEC 61850 series, introducing new requirements operating on layer 2 networks, according to IEC 61850-8-1 and IEC 61850-9-2. The seamless redundancy principle has been extended to clocks operating according to the Precision Time Protocol (IEC 61588) and attached to redundant networks. Two variants are specified: L3E2E for clocks which operate on layer 3 networks with end-to-end link delay measurement (E2E) and L2P2P for clocks that operate on layer 2 with peer-to-peer link delay measurement (P2P). 0.2 Changes with respect to the previous edition The major changes with respect to IEC 62439-3:2010 are listed below. Aligning the sequence number between PRP and HSR, to enable coupling of HSR and PRP networks and simplify the implementation of dual-mode nodes in hardware. At the same time, introduce a suffix in the PRP Redundancy Control Trailer to allow better identification, future extensions and coexistence with other protocols that also happen to use a trailer. This change is not backwards-compatible, so means are provided to identify the version and ensure that the networks are homogeneous. Removing all implementation restrictions on the Duplicate Discard algorithm (especially r

Scope: The IEC 62439 series is applicable to high-availability automation networks based on the ISO/IEC 8802-3 Ethernet technology. This part of IEC 62439 specifies two redundancy protocols designed to provide seamless recovery in case of single failure of an inter-bridge link or bridge in the network, which are based on the same scheme: duplication of the LAN, resp. duplication of the transmitted parallel transmission of duplicated information.

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope
  • 4.1.1 PRP network topology
  • 4.1.2 PRP LANs with linear or bus topology
  • 4.1.3 PRP LANs with ring topology
  • 4.1.4 DANP node structure
  • 4.1.5 PRP attachment of singly attached nodes
  • 4.1.6 Compatibility between singly and doubly attached nodes
  • 4.1.7 Network management
  • 4.1.8 Implication on configuration application
  • 4.1.9 Transition to non-redundant networks
  • 4.1.10 Duplicate handling
  • 4.1.11 Network supervision
  • 4.1.12 Redundancy management interface
  • 4.2.1 Installation, configuration and repair guidelines
  • 4.2.2 Unicast MAC addresses
  • 4.2.3 Multicast MAC addresses
  • 4.2.4 IP addresses
  • 4.2.5 Nodes
  • 4.2.6 Duplicate Accept mode (testing only)
  • 4.2.7 Duplicate Discard mode
  • 4.3.2 PRP_Supervision frame contents
  • 4.3.3 PRP_Supervision frame for RedBox
  • 4.3.4 Reception of a PRP_Supervision frame and NodesTable
  • 4.3.1 PRP_Supervision frame format
  • 5.2.1 Basic operation with a ring topology

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC 62439-3 (REDLINE + STANDARD)-2016 PDF

IEC 62439-3 (REDLINE + STANDARD)-2016 PDF

$509.45 $1,018.89