IEC 62642-1-2010 PDF

IEC 62642-1-2010 PDF

Alarm systems-Intrusion and hold-up systems-Part 1: System requirements

$186.00 $371.99 -50%
Product Code: IEC 62642-1
Stock In Stock
Edition: 1.0
Published: 06/2010
Number of Pages: 96
File Size: 1 file, 1 Byte

Available Options

Product Description

Alarm systems – Intrusion and hold-up systems – Part 1: System requirements

Introduction: This standard is part of the IEC 62642 series of International Standards and Technical Specifications “Alarm systems – Intrusion and hold-up systems”, written to include the following parts: Part 1 System requirements Part 2-2 Intrusion detectors – Passive infrared detectors Part 2-3 Intrusion detectors – Microwave detectors Part 2-4 Intrusion detectors – Combined passive infrared / Microwave detectors Part 2-5 Intrusion detectors – Combined passive infrared / Ultrasonic detectors Part 2-6 Intrusion detectors – Opening contacts (magnetic) Part 2-71 Intrusion detectors – Glass break detectors – Acoustic Part 2-72 Intrusion detectors – Glass break detectors – Passive Part 2-73 Intrusion detectors – Glass break detectors – Active Part 3 Control and indicating equipment Part 4 Warning devices Part 5-3 Requirements for interconnections equipment using radio frequency techniques Part 6 Power supplies Part 7 Application guidelines Part 8 Security fog devices This International Standard applies to Intrusion and Hold-up Alarm Systems (I&HAS). The standard is also intended to apply to Intruder Alarm Systems (IAS) which include only intrusion detectors and to Hold-up Alarm Systems (HAS) which include only hold-up devices. This International Standard is a specification for Intrusion and Hold-up Alarm Systems installed in buildings, it includes four security grades and four environmental classes. The purpose of an I&HAS is to enhance the security of the supervised premises. To maximise it

Scope: This part of IEC 62642 specifies the requirements for Intrusion and Hold-up Alarm Systems (I&HAS) installed in buildings using specific or non-specific wired interconnections or wire-free interconnections. These requirements also apply to the components of an I&HAS installed in a building which are normally mounted on the external structure of a building e.g. ancillary control equipment or warning devices. The standard does not include requirements for exterior I&HAS. This International Standard specifies performance requirements for installed I&HAS but does not include requirements for design, planning, installation, operation or maintenance. These requirements also apply to I&HAS sharing means of detection, triggering, interconnection, control, communication and power supplies with other applications. The functioning of an I&HAS is not adversely influenced by other applications. Requirements are specified for I&HAS components where the relevant environment is classified. This classification describes the environment in which an I&HAS component may be expected to function as designed. When the requirements of the four environmental classes are inadequate, due to the extreme conditions experienced in certain geographic locations, special national conditions are given in Annex A. General environmental requirements for I&HAS components are described in Clause 7. The requirements of this standard also apply to IAS and HAS when these systems are installed independently. When an I&HAS does not include functions relating to the detection of intruders, the requirements relating to intrusion detection do not apply. When an I&HAS does not include functions relating to hold-up, the requirements relating to hold-up do not apply. NOTE Unless otherwise stated, the abbreviation I&HAS is also intended to mean IAS and HAS.

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope
  • 8.3.10 Inhibit
  • 8.3.11 Isolate
  • 8.3.12 Test
  • 8.3.13 Other functions

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC 62642-1-2010 PDF

IEC 62642-1-2010 PDF

$186.00 $371.99