IEC 62282-6-100-2012 PDF

IEC 62282-6-100-2012 PDF

Fuel cell technologies-Part 6-100: Micro fuel cell power systems-Safety

$775.52 $1,551.03 -50%
Product Code: IEC 62282-6-100
Stock In Stock
Edition: 1.1
Published: 10/2012
Number of Pages: 390
File Size: 1 file, 3.4 MB

Available Options

Product Description

Fuel cell technologies – Part 6-100: Micro fuel cell power systems – Safety

Scope: 1.1 General a) This consumer safety standard covers micro fuel cell power systems, micro fuel cell power units and fuel cartridges that are wearable or easily carried by hand, providing d.c. outputs that do not exceed 60 V d.c. and power outputs that do not exceed 240 VA. Portable fuel cell power systems that provide output levels that exceed these electrical limits are covered by IEC 62282-5-1. b) Externally accessible circuitry is therefore considered to be safety extra low voltage (SELV) circuitry as defined in IEC 60950-1:2005, and as limited power circuits if further compliance with 2.5 of IEC 60950-1:2005 is demonstrated. Micro fuel cell power systems or units that have internal circuitry exceeding 60 V d.c. or 240 VA should be appropriately evaluated in accordance with the separate criteria of IEC 60950-1:2005. c) This consumer safety standard covers all micro fuel cell power systems, micro fuel cell power units and fuel cartridges. This standard establishes requirements for all micro fuel cell power systems, micro fuel cell power units and fuel cartridges to ensure a reasonable degree of safety for normal use, reasonably foreseeable misuse, and consumer transportation of such items. The fuel cartridges covered by this standard are not intended to be refilled by the consumer. Fuel cartridges refilled by the manufacturer or by trained technicians shall meet all requirements of this standard. d) These products are not intended for use in hazardous areas as defined by IEV 426-03-01. 1.2 Fuels and technologies covered a) A micro fuel cell power system block diagram is shown in Figure 1. b) All portions of this standard, including all annexes, apply to micro fuel cell power systems, micro fuel cell power units and fuel cartridges as defined in Subclause 1.1 above. c) Clauses 1 through 7 of this standard cover direct methanol fuel cells using methanol or methanol and water solutions as fuel. Clauses 1 through 7 cover specific requirements for direct methanol fuel cells using proton exchange membrane technologies. Clauses 1 through 7 also cover general requirements applicable to all fuel cell technologies and all fuels covered in Annexes A through H. d) Annexes

Contents:

  • FOREWORD
  • Scope
  • 4.10 Protection against fire, explosion, corrosivity and toxicity hazard
  • 4.11 Protection against electrical hazards
  • 4.12 Fuel supply construction
  • 4.12.1 Fuel cartridge construction
  • 4.12.2 Fuel cartridge fill requirement
  • 4.13 Protection against mechanical hazards
  • 4.13.1 Piping and tubing other than fuel lines
  • 4.13.2 Exterior surface and component temperature limits
  • 4.13.3 Motors
  • 4.14 Construction of electric device components
  • 4.14.1 Limited power sources
  • 4.14.2 Devices that use electronic controllers
  • 4.14.3 Electrical conductors/wiring
  • 4.14.4 Output terminal area
  • 4.14.5 Electric components and attachments
  • 4.14.6 Protection

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC 62282-6-100-2012 PDF

IEC 62282-6-100-2012 PDF

$775.52 $1,551.03