IEC 62599-1-2010 PDF

IEC 62599-1-2010 PDF

Alarm systems-Part 1: Environmental test methods

$163.93 $327.86 -50%
Product Code: IEC 62599-1
Stock In Stock
Edition: 1.0
Published: 05/2010
Number of Pages: 78
File Size: 1 file, 1 Byte

Available Options

Product Description

Alarm systems – Part 1: Environmental test methods

Introduction: The purpose of environmental testing is to demonstrate that the equipment can operate correctly in its service environment and that it will continue to do so for a reasonable time. Alarm system equipment is, however, installed in many very different environments and it would be impractical to test every aspect of the most extreme conceivable environmental conditions. The tests and severities listed in this part of IEC 62599 are, therefore, intended to provide a practical series of tests to determine the ability of the equipment to withstand the failure mechanisms most likely to be produced by the environment, in which that type of equipment can be expected to be installed (i.e. the normal service environment). This part includes only service environments, which relate to equipment installed in general industrial/commercial premises. Hence it should be noted that, additional precautions may be necessary, in particular installations, where some aspects of the environment can be identified as being unusually severe. A special additional severity has been added to the cold test, to cater for the especially cold conditions found in the very north of Europe. The tests are intended to demonstrate failures due to realistic service environments. However, some significant failure mechanisms are brought about by changes which occur slowly under these realistic service conditions. In order to make tests in a practical and economic time, it is sometimes necessary to accelerate these chang

Scope: This part of IEC 62599 specifies environmental test methods to be used for testing the system components of the following alarm systems, intended for use in and around buildings: a) access control systems, for security applications; b) alarm transmission systems1; c) CCTV systems, for security applications; d) combined and/or integrated systems; e) intruder and hold-up alarm systems; f) remote receiving and/or surveillance centres; g) social alarm systems. This part specifies three equipment classes (fixed, movable and portable equipment) and four environmental classes. The environmental classes only include the general service environments envisaged for equipment installed in typical residential, commercial and industrial environments. It may be necessary for the product standard to require additional or different environmental tests or severities where 1) there could be specific environmental problems (e.g. some different severities may be required for break glass detectors stuck to glass windows, due to the local extremes of temperature and humidity), 2) the test exposure falls within the intended detection phenomenon of the detector (e.g. during a vibration test on a seismic detector). In order to provide reproducible test methods and to avoid the proliferation of technically similar test methods, the test procedures have been chosen, where possible, from internationally accepted standards. (e.g. IEC publications). For specific guidance on these tests, reference should be made to the appropriate document, indicated in the relevant subclauses. For more general guidance and background information on environmental testing reference should be made to IEC 60068-1 and IEC 60068-3. This standard does not specify i) the requirements or performance criteria to be applied, which should be specified in the relevant product standard, ii) special tests only applicable to a particular device (e.g. the effects of turbulent air draughts on ultrasonic movement detectors), iii) basic safety requirements, such as protection against electrical shocks, unsafe operation, insulation coordination and related dielectric tests, iv) tests relating to deliberate acts of damage or tampe

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope
  • 10 Cold (operational)
  • 10.1 Object of the test
  • 10.2 Principle
  • 10.3 Test procedure
  • 10.3.1 General
  • 10.3.2 Initial measurements
  • 10.3.3 State of specimen during conditioning
  • 10.3.4 Conditioning
  • 10.3.5 Measurements during conditioning
  • 10.3.6 Final measurements
  • 11 Temperature change (operational)
  • 11.1 Object of the test
  • 11.2 Principle
  • 11.3 Test procedure

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC 62599-1-2010 PDF

IEC 62599-1-2010 PDF

$163.93 $327.86