Electric vehicle conductive charging system - Part 27: EV supply equipment with automatic docking of a vehicle coupler according to IEC 62196-2, IEC 62196-3 or IEC TS 62196-3-1
Introduction: This part of the IEC 61851 series provides requirements for EV supply equipment with automatic docking for the transfer of electric energy between EV supply equipment and electric road vehicles. The vehicle and the EV supply equipment make up a complete system that is covered by a number of IEC and ISO Standards. Automatic docking is indispensable for autonomous vehicles, and it is also helpful for disabled users of electric vehicles and for all users of electric vehicles seeking additional comfort. In the case of public electric vehicle supply equipment, automatic docking can also provide a convenient solution for queued vehicles, through automatic electric vehicle supply equipment that is either fully mobile or movable on rails. Automatic docking can increase the number of electric vehicles that are available to the grid to provide grid services. Within the IEC 61851 series, the following documents cover different aspects of automatic docking: IEC 61851-23-11: DC electric vehicle charging station with an automated connection device; IEC TS 61851-26: EV supply equipment with automatic docking of a vehicle coupler located at the underbody of an electric vehicle; IEC TS 61851-282: Communication between EV supply equipment with automatic docking and vehicles. Automatic docking enables conductive energy transfer at the complete range of voltage and current as specified in the following documents: IEC 61851-1: General requirements, which is a system standard that serves as a basi
Scope: This document, in combination with IEC 61851-1 or IEC 61851-23, gives the requirements for EV supply equipment with automatic docking and undocking functions (aEVSE) of a vehicle coupler according to IEC 62196-2, IEC 62196-3 or IEC TS 62196-3-1 for power transfer with electrically propelled road vehicles according to ISO TS 5474-5. Use of aEVSE with the megawatt charging system is under consideration. NOTE 1 Where this document refers to IEC 61851-23 and IEC 62196-3 or IEC TS 62196-3-1, it is intended to alternatively use IEC 61851-23-3 and IEC TS 63379 4. This document provides requirements for aEVSE with a single vehicle connector. Requirements for aEVSE with more than one vehicle connector are under consideration. This document only applies to aEVSE with automatic couplers of category 1, which use a vehicle coupler defined by IEC 62196-2, IEC 62196-3 or IEC TS 62196-3-1. NOTE 2 Category 1 is planned to also include the use of an electro-mechanical interface defined by IEC TS 63379. This document only specifies automatic conductive energy transfer using a vehicle connector and a vehicle inlet; it does not specify automatic conductive power transfer using a plug and a socket-outlet. This document does not apply to aEVSE with automatic couplers of category 2, which use an electro-mechanical interface defined by EN 50696. NOTE 3 Category 2 is planned to also include the use of an electro-mechanical interface defined by IEC 63407 5. This document does not apply to aEVSE with automatic coupler of category 3 (see IEC TS 61851-26). NOTE 4 Category 3 is planned to use the electro-mechanical interface for AC up to 22 kW defined by IEC TS 63644 6. Another document that extends category 3 and defines an electro-mechanical interface for combined AC/DC power transfer is under consideration. EMC requirements for EV supply equipment are defined in IEC 61851-21-2. Interoperable communication for docking and undocking between an aEVSE and an EV, extending the communication between an EV supply equipment and an EV as specified in IEC 61851-1, IEC 61851-23, IEC 61851-24 and the ISO 15118 series, is under consideration. NOTE 5 Where this document refers to "interoperable communic
Contents:
- FOREWORD
- INTRODUCTION
- Scope
- 10.10 Mechanical impact