IEC TS 63107-2020 PDF

IEC TS 63107-2020 PDF

Integration of internal arc-fault mitigation systems in power switchgear and controlgear assemblies (PSC assemblies) according to IEC 61439-2

$163.93 $327.86 -50%
Product Code: IEC TS 63107
Stock In Stock
Edition: 1.0
Published: 04/2020
Number of Pages: 79
File Size: 1 file, 3 Bytes

Available Options

Product Description

Integration of internal arc-fault mitigation systems in power switchgear and controlgear assemblies (PSC assemblies) according to IEC 61439-2

Introduction: Internal arc-fault mitigation systems (IAMS) denote systems that consist of an internal arc- fault control device (IACD) and an internal arc-fault reduction device (IARD). An IACD and an IARD can be combined and designed in one device. An IACD uses the effects of an arc, e.g. light, gas pressure, change of current and/or voltage to detect an arc inside the power switchgear and controlgear assembly (PSC-assembly) to generate a trigger signal for an associated IARD. An IARD reduces the arc energy below the level which would be released if an IARD was not present and the fault would be interrupted by the conventional short-circuit protective device (SCPD). The operation of IARDs can be achieved by various methods, individually or in combination including, but not limited to, the following examples: a) by interruption using an upstream SCPD triggered by an IACD; b) by parallel connection of a low-impedance current path by using an arc quenching device (AQD) for commutation of current to this parallel path. The operation of an upstream SCPD is also required to interrupt the short-circuit current caused by the AQD before it exceeds its current carrying capabilities; c) by introducing a defined impedance in series with the arc-fault circuit by using an internal arc-fault limiting device (IALD). An upstream SCPD may be required to extinguish the arc. The most commonly used techniques are described under a) and b) above. The purpose of this document is: to define the specific requirem

Scope: This document states requirements for integration and testing of IAMS in low-voltage switchgear and controlgear assemblies – power switchgear and controlgear assemblies according to IEC 61439-1 and IEC 61439-2 (PSC-assemblies) to demonstrate their correct operation. This document does not address personnel safety or damage to the PSC-assembly. These requirements are dealt with in IEC TR 61641 (see also 10.10.1). NOTE This document can be used as a reference for other types of assemblies in the IEC 61439 series, but adaptation of the test procedures and acceptance criteria can apply taking into account the specifics of such other assemblies or products. IAMS consist of IACDs and IARDs complying with their relevant product standard (e.g. optical based IACDs in accordance with IEC 60947-9-2, AQDs in accordance with IEC 60947-9-1 and SCPD’s in accordance with IEC 60947-2). For the reliable function in a PSC-assembly, the verification of correct operation of the complete system under built-in conditions is addressed. This document applies only to enclosed PSC-assemblies and deals with all required verifications needed for the integration in conjunction with IEC 61439-1 and IEC 61439-2. The test procedure given in this document takes into consideration: the correct function of the IAMS within the PSC-assembly; the prevention of unintended operation of the IAMS within the PSC-assembly; the functioning behaviour of the system immediately after the assembly is energised. Different tests under more severe conditions (e.g. doors in open position) can be performed with an agreement between the user and the original manufacturer of the PSC-assembly. This document does not supersede any individual product standard. Individual devices are required to comply with their relevant standard. This document does not apply to integration of arc fault detection devices (AFDD) according to IEC 62606. The informative Annex II gives guidance on particular constructional requirements for incorporation of IAMS within a PSC-assembly. The informative Annex HH gives guidance for the user of PSC-assemblies about the criteria to be considered when specifying a PSC-assembly with an integrated IAM

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope
  • 3 gG AC 400 V IEC 60269-2

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC TS 63107-2020 PDF

IEC TS 63107-2020 PDF

$163.93 $327.86