IEC TS 62578-2015 PDF

IEC TS 62578-2015 PDF

Power electronics systems and equipment-Operation conditions and characteristics of active infeed converter (AIC) applications including design recommendations for their emission values below 150 kHz

$255.36 $510.71 -50%
Product Code: IEC TS 62578
Stock In Stock
Edition: 2.0
Published: 04/2015
Number of Pages: 244
File Size: 1 file, 6 Bytes

Available Options

Product Description

Power electronics systems and equipment – Operation conditions and characteristics of active infeed converter (AIC) applications including design recommendations for their emission values below 150 kHz

Introduction: This revision of the technical specification IEC TS 62578 is necessary because active infeed converters (AIC) are a state of the art technology in power electronic products and will be of major importance in order to realize the "smart grid" and the "energy efficiency" initiatives. AICs in industrial and domestic use are necessary to feedback energy from an energy source (e.g. solar panels, fuel cells or wind turbines) or from a motor load to the power supply network and make it available for other consumers instead of dissipating it as a waste-heat to the environment. Dispersed power generating equipment uses AICs to synchronise their voltages and currents to the power supply network or to exchange electrical energy between energy storage devices such as batteries and consumers. Utilities will require information on how to correctly apply the AICs in order to mitigate harmonics in the power supply network. AICs can also be used to mitigate pre-existing harmonics in the supply system – information on this is of interest to utilities. Different possible topologies of AICs are described together with their specific advantages. Warning: The recommendations of maximum emission values for conducted emissions <150 kHz defined in this document are based on observations and experience gained from state of the art AICs operating today in most power supply networks together with other equipment without creating intolerable interference and should lead to an increased acceptance of usin

Scope: This Technical Specification IEC TS 62578 describes the operation conditions and typical characteristics of active infeed converters (AIC) of all technologies and topologies which can be connected between the electrical power supply network (lines) a.c. side and a constant current or voltage type d.c. side and which can convert electrical power (active and reactive) in both directions (generative or regenerative). Applications with active infeed converters are commonly used with the d.c. sides of adjustable speed power drive systems (PDS), uninterruptible power systems (UPS), active filters, photovoltaic systems, wind turbine systems, battery backed power management systems etc. of all voltages and power ratings. Active infeed converters are generally connected between the electrical power supply network (a.c. side) and a current or voltage d.c. side, with the objective to avoid emitting low frequency harmonics (e.g. less than 1 kHz) by synthesizing a sinusoidal a.c. current. Some of them can additionally compensate the pre-existing harmonic distortion of a given supply side voltage. They are moreover able to control the power factor of a power supply network section by moving the electrical power (active and reactive) in both directions (generative or regenerative), which enables energy saving in the system and stabilizes the power supply voltage or enables coupling of renewable energy sources or electrical energy storage devices to the supply. A practical and analytical approach for emission values for AICs in power supply networks is given, which is based on the latest results for line impedance values between 2 kHz and 9 kHz and withstand capability of capacitors connected directly to the supply. This results in design recommendations for emission values below 150 kHz. The following is excluded from the scope. Requirements for the design, development or further functionality of active infeed applications. Probability of interactions or influences of the AIC with other equipment caused by parasitic elements in an installation or caused by poor electronic design as well as their mitigations. "Overhead line" power supply networks because of lack of information

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope
  • 2 kHz to 20 kHz

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC TS 62578-2015 PDF

IEC TS 62578-2015 PDF

$255.36 $510.71