IEC TS 62647-1-2012 PDF

IEC TS 62647-1-2012 PDF

Process management for avionics-Aerospace and defence electronic systems containing lead-free solder-Part 1: Preparation for a lead-free control plan

$163.93 $327.86 -50%
Product Code: IEC TS 62647-1
Stock In Stock
Edition: 1.0
Published: 08/2012
Number of Pages: 36
File Size: 1 file, 344 Bytes

Available Options

Product Description

Process management for avionics – Aerospace and defence electronic systems containing lead-free solder – Part 1: Preparation for a lead-free control plan

Introduction: The European Union (EU) enacted two directives; 2002/95/EC Restriction of Hazardous Substances (RoHS) and 2002/96/EC Waste Electrical and Electronic Equipment (WEEE) that restrict or eliminate the use of various substances in a variety of products that are put on the market after July 2006. Other countries have also enacted similar legislation. One of the key materials restricted is lead (Pb), which is widely used in electronic solder and electronic piece part terminations. These regional regulations affect the global market place. However, due to the reduced market share of the Aerospace, Defence and High Performance (ADHP) industries, many of the lower tier suppliers to those industries will change their products to serve their primary, non-ADHP markets. Additionally, several United States (US) states have enacted similar “green” laws and many Asian electronics manufacturers have recently announced completely green product lines. Since ADHP is one of the few major industrial sectors that still repair circuit card assemblies (CCAs) and the Pb-free materials and processes are relatively immature and not fully understood, an aerospace-wide approach to their application is desired. The products of ADHP companies developing and/or managing Pb-free electronics fall into one of the five categories below. 1) Products that have been designed and qualified with traditional tin-lead (SnPb) electronic piece parts, materials, and assembly processes, and that will need to be maintained i

Scope: This part of the IEC/TS 62647 series defines the objectives of, and requirements for, documenting processes that assure customers and regulatory agencies that ADHP electronic systems containing Pb-free solder, piece parts, and PWBs will satisfy the applicable requirements for performance, reliability, airworthiness, safety, and certifiability throughout the specified life of performance. This specification aims to communicate requirements for a lead-free control plan (LFCP), hereinafter referred to as the Plan, and to assist the Plan owners in the development of their own Plans. The Plan documents the Plan owner’s processes to assure their customers and all other stakeholders that the Plan owner’s products will continue to meet their requirements, given the risks stated in the Introduction. This specification does not contain detailed descriptions of the processes to be documented but lists high-level requirements for such processes, and areas of concern to the ADHP industries that need to be addressed by the processes. Pb-free risk management should be accomplished through specific requirements added to the Plan owner’s existing infrastructure of product management and control. This specification applies to the ADHP electronics system supply chain. The control of the Pb-free activities will be accomplished by the Plan owner addressing the requirements of their Customer. These activities include, but are not limited to, those performed by the system integrator, the original equipment manufacturer (OEM), and their respective supply chains, to the lowest level possible. This should be done with the knowledge that, at the component level, the aerospace industry may not have a great influence over those suppliers. In such cases, the Plan owner assumes responsibility. Some applications may have unique requirements that exceed the scope of this specification. The extended scope should be covered separately. The requirements of this specification may be tailored to address unique/specific program needs. If tailoring is performed, the user will obtain documented customer concurrence. Annex A provides a tailoring template that may be used. This document may be used by ot

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC TS 62647-1-2012 PDF

IEC TS 62647-1-2012 PDF

$163.93 $327.86