IEC TS 62647-3-2014 PDF

IEC TS 62647-3-2014 PDF

Process management for avionics-Aerospace and defence electronic systems containing lead-free solder-Part 3: Performance testing for systems containing lead-free solder and finishes

$186.00 $371.99 -50%
Product Code: IEC TS 62647-3
Stock In Stock
Edition: 1.0
Published: 02/2014
Number of Pages: 46
File Size: 1 file, 590 Bytes

Available Options

Product Description

Process management for avionics – Aerospace and defence electronic systems containing lead-free solder – Part 3: Performance testing for systems containing lead-free solder and finishes

Introduction: The implementation of lead-free (Pb-free) interconnection technology into electronics has resulted in a variety of reactions by designers, manufacturers, and users. While the prime motivation for lead-free (Pb-free) technology was to address the social concern of improving the environment by limiting the amount of toxic and dangerous substances used in products, the ramifications of this initiative have provided a state of uncertainty regarding the performance – in this context, defined as operation and reliability, i.e. the expected life cycle of a product – of aerospace and defence systems. For over fifty years, tin-lead solder was the benchmark for electronics assembly and generations of research baselined its performance under a variety of operating conditions including the harsh settings of aerospace and defence equipment. However, with the integration of lead-free (Pb-free) technology, aerospace and defence companies are faced with questions as to whether these new materials will provide, as a minimum, the same degree of confidence during the life cycle of critical systems and products. In evaluating performance, two approaches are used: analysis/modelling and test. This document addresses the latter, providing guidance and direction in the development and execution of performance tests for lead-free (Pb-free) electronic interconnections. The user of this document needs to be aware of the following: This document does not give answers as to how to perform a specific tes

Scope: This part of the IEC 62647 series defines for circuit card assemblies (CCA): a default method for those companies that require a pre-defined approach, and a protocol for those companies that wish to develop their own test methods. The intent of this document is not to prescribe a certain method, but to aid avionics/defence suppliers in satisfying the reliability and/or performance requirements of IEC/TS 62647-1 as well as support the expectations in IEC/TS 62647-21. The default method (see Clause 5) is intended for use by electronic equipment manufacturers, repair facilities, or programs that, for a variety of reasons, may be unable to develop methods specific to their own products and applications. It should be used when little or no other information is available to define, conduct, and interpret results from reliability, qualification, or other tests for electronic equipment containing lead-free (Pb-free) solder. The default method is intended to be conservative, i.e., it is biased toward minimizing the risk to users of ADHP electronic equipment. The protocol (see Clause 6) is intended for use by manufacturers or repair facilities that have the necessary resources to design and conduct reliability, qualification, or process development tests that are specific to their products, their operating conditions, and their applications. Users of the protocol will have the necessary knowledge, experience, and data to customize their own methods for designing, conducting, and interpreting results from the data. Key to developing a protocol is a firm understanding of all material properties for the lead-free (Pb-free) material in question as well as knowledge of package- and board-level attributes as described in 5.3.2. As an example, research has shown that the mechanisms for creep can be different between tin-lead and tin-silver-copper (SAC) solders. Understanding these mechanisms is key to determining critical test parameters such as dwell time for thermal cycling. The protocol portion of this document provides guidance on performing sufficient characterization of new materials in order to accurately define test parameters. Use of the protocol is encouraged, since it

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC TS 62647-3-2014 PDF

IEC TS 62647-3-2014 PDF

$186.00 $371.99