ISO 11301-1-2026 PDF

ISO 11301-1-2026 PDF

Piping systems for rehabilitation of underground gas supply networks-Part 1: Polyethylene (PE) material

$129.00 $258.00 -50%
Product Code: ISO 11301-1 (2026)
Stock In Stock
Edition: 1.
Published: 07/2026
Number of Pages: 48
File Size: 1 file, 1.8 MB

Available Options

Product Description

Piping systems for rehabilitation of underground gas supply networks — Part 1: Polyethylene (PE) material

Introduction: This document is a part of a series of International Standards for piping systems of various materials used for the rehabilitation of existing pipelines in a specified application area. Standards for rehabilitation deal with the following applications: — the ISO 11300 series: Piping systems for rehabilitation of underground drains, sewers and water supply networks; — the ISO 11301 series: Piping systems for rehabilitation of underground gas supply networks. The ISO 11300 series and the ISO 11301 series are subdivided into parts covering a specific material per pipe system. The ISO 11300 series is subdivided into four parts: — Part 1: Polyethylene (PE) material; — Part 2: Thermoset composite materials; — Part 3: Polyvinyl chloride (PVC-U) material; — Part 4: Thermoplastic composite materials. The ISO 11301 series currently consists of two parts: — Part 1: Polyethylene (PE) material (this document); — Part 5: Unplasticized Polyamide (PA-U) material.1) These series of standards cover various techniques for renovation and trenchless replacement. Furthermore, they are distinguished from those for conventionally installed plastics piping systems by the requirement to verify certain characteristics in the “as-installed” condition, after site processing. This is in addition to specifying requirements for piping system components “as manufactured”. A consistent structure of clause headings has been adopted for all parts of the ISO 11300 series and the ISO 11301 series, in order to fac

Scope: This document specifies requirements and test methods for pipes and fittings which are part of piping systems for the rehabilitation, by means of renovation and trenchless replacement, of underground gas supply networks. It is applicable to polyethylene (PE) pipes, fittings and assemblies, as manufactured and as installed. It is not applicable to the existing pipeline. This document is applicable to the following technique families for renovation, intended to be used at an operating temperature of 20 °C as a reference temperature: — lining with continuous pipes; — lining with close-fit pipes. This document is applicable to the following technique families for trenchless replacement, intended to be used at an operating temperature of 20 °C as a reference temperature: — pipe bursting and pipe extraction; — horizontal directional drilling and impact moling. This document is applicable to: — PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes; — PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex D, where all layers have the same minimum required strength (MRS) rating. Furthermore, when used with lining with continuous pipes and trenchless replacement, this document is applicable to: — PE coated pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe (“coated pipe”), as specified in Annex D. NOTE When used with lining with close-fit lining pipes, the lining pipe is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner. This document is applicable to jointing by means of butt fusion and electrofusion and to fabricated and injection-moulded fittings and mechanical connections of PE. This document is not applicable to push-fit jointed discrete pipes assembled as part of the trenchless installation process. © ISO 2026 – All rights reserved ISO 11301-1:2026(en) 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this docume

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ISO 11301-1-2026 PDF

ISO 11301-1-2026 PDF

$129.00 $258.00