Lifts for the transport of persons and goods — Part 3: Requirements from other Standards (ASME A17.1/CSA B44 and JIS A 4307- 1/JIS A 4307-2) not included in ISO 8100-1 or ISO 8100-2
Introduction: The elevator industry has become increasingly international in nature resulting in the rationalization of many local standards and their harmonization with international Standards. ISO 8100-1 and ISO 8100-2 address the requirements in many parts of the world. However, there are standards applicable in regions of the world such as North America and Japan that have differences in specific prescriptive requirements from those in ISO 8100-1 and ISO 8100-2. This document needs to be used in combination with ISO 8100-1 and ISO 8100-2 for the purpose of achieving equivalency with the requirements of ASME A17.1/CSA B44 and JIS A 4307-1/JIS A 4307-2 respectively, where the scopes of ASME A17.1/CSA B44 and JIS A 4307-1/JIS A 4307-2 coincide with the scope of ISO 8100-1 and ISO 8100-2. Equipment outside of the scope of ISO 8100-1 and ISO 8100-2 is not addressed in this document. While the scope of ISO 8100-1 and ISO 8100-2 addresses electric as well as hydraulic lifts, this document only addresses electric lifts (except home lifts). Future editions of this document will address hydraulic lifts, home lifts, as well as, electric lifts. This document identifies section and requirement numbers from ASME A17.1/CSA B44 or JIS A 4307- 1/JIS A 4307-2 for requirements to be used in addition to, or in place of, specific clauses in ISO 8100-1 and ISO 8100-2. The content of the specific requirements is published in ASME A17.1/CSA B44 and JIS A 4307-1/JIS A 4307-2. This document is not a substitute
Scope: 1.1 This document specifies the safety rules for permanently installed new passenger or goods passenger lifts, with traction, positive or hydraulic drive, serving defined landing levels, having a car designed for the transportation of persons or persons and goods, suspended by ropes, chains or jacks and moving between guide rails inclined not more than 15° to the vertical. 1.2 This document covers the machinery described in 1.1 and the hazards, hazardous situations and hazardous events related to their use. NOTE Supplementary requirements can apply in special cases (use of lifts by persons with disabilities, in case of fire, potentially explosive atmosphere, extreme climate conditions, seismic conditions, transporting dangerous goods, etc.). 1.3 This document does not cover: a) lifts with: 1) drive systems other than those stated in 1.1; 2) rated speed ≤0,15 m/s; b) hydraulic lifts: 1) with a rated speed exceeding 1 m/s; 2) where the setting of the pressure relief valve (5.9.3.5.3) exceeds 50 MPa; c) new passenger or goods passenger lifts in existing buildings1) where, in some circumstances, some requirements of ISO 8100-1 cannot be met due to limitations enforced by building constraints and local requirements, e.g. EN 81-21, should be considered; d) lifting appliances, such as paternosters, mine lifts, theatrical lifts, appliances with automatic caging, skips, lifts and hoists for building and public works sites, ships' hoists, platforms for exploration or drilling at sea, construction and maintenance appliances or lifts in wind turbines; e) important modifications (see Annex C) to a lift installed before this document is brought into application; f) safety during operations of transport, erection, repairs, and dismantling of lifts. However, this document can usefully be taken as a basis. 1) Existing building is a building which is used or was already used before the order for the lift was placed. A building whose internal structure is completely renewed is considered as a new building. TECHNICAL SPECIFICATION ISO/TS 8100-3:2019(E) © ISO 2019 – All rights reserved ISO/TS 8100-3:2019(E) Noise and vibrations are not dealt with in this document as they are not f